Chertyozh Grindera G9
• To obtain the Illustrated Parts Catalog, visit the Bunn-O-Matic website, at www.bunn.com. This is absolutely FREE, and the quickest way to obtain the catalog. Contact Bunn-O-Matic Corporation at 1-800-286-6070 to obtain a paper copy of the required Illustrated Parts Catalog mailed via U.S. Postal Service. • AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND.
Test run for grinder thermorming sheet on an Adler grinder model G9. G9-2 HD G9-2T HD G9-2 HD-S INSTALLATION & OPERATING GUIDE BUNN-O-MATIC CORPORATION POST OFFICE BOX 3227. If grinder has an analog timer, proceed to step 6.
In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities or services, or any other special, incidental or consequential damages. • FAILURE TO COMPLY RISKS EQUIPMENT DAMAGE, FIRE, OR SHOCK HAZARD READ THE ENTIRE OPERATING MANUAL INCLUDING THE LIMIT OF WARRANTY AND LIABILITY BEFORE BUYING OR USING THIS PRODUCT D 01/04 © 1990 Bunn-O-Matic Corporation # CARAFE Page 3 P1300 07. • The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all surfaces on Bunn-O-Matic equipment. Care should be taken not to scratch the windows with any abrasive mate- rial. Regular cleaning will keep your grinder looking new for years. • ADJUSTMENTS (cont.) Burr Adjustment (cont.) Make a mark with a pen on the decal to note the position of the arrow on the grind adjustment screw.
The following settings approximately correspond to the CBC recognized grinds. All are referenced from the arrow position noted in step 7. FINE GRIND: Rotate the adjusting screw 7 hash marks in a counterclockwise direction. • TROUBLESHOOTING A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems encountered.
If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic Technical Service Department. • Inspection, testing, and repair of electrical equipment should be performed only by qualified service per- sonnel. • TROUBLESHOOTING (cont.) Problem Grinder will not start. (cont.) Grinder will not shut off. Grinder starts, but will not dis- pense.
Incorrect amount of coffee. Incorrect coffee grind dispensed. Probable Cause 4. Off/On/Start switch 2.
• SERVICE This section provides procedures for testing and replacing various major components used in this grinder should service become necessary. Refer to Troubleshooting for assistance in determining the cause of any problem. WARNING - Inspection, testing, and repair of electri- cal equipment should be performed only by qualified service personnel. • SERVICE (cont.) Motor F IN F IN IN JU S AN FI NG T OF E OP Location: The motor is located in the upper wrapper under the hopper. Test Procedure: Remove the hole plug located on the right side of the housing. • SERVICE (cont.) Motor (cont.) 1. Adjusting Screw Locknut 2.
Adjusting Screw 3. Burr Housing Cap 4. Shear Plate Removal and Replacement - GRIND CHAMBER Refer to the illustration above and remove the two 1/4”-20, hex head screws holding the burr housing cap(3) to the burr housing. Huawei p6 u06 firmware. • SERVICE (cont.) Off/On/Start Switch CARAFE Location: The Off/On/Start switch is centered in the housing above the upper front inspection panel. Test Procedure: 1. Disconnect the grinder from the power supply.
Remove the black wire from the switch. Check for continuity across the black wire from the Off/On/Start switch and the left blade of the cordset connector (see illustration below). • SERVICE (cont.) If continuity is not present as described, replace the switch. Removal and Replacement: Remove all the wires from the switch termi- nals. Compress the clips inside the housing and gently push the switch through the opening. Push the new switch into the opening and spead the clips to hold the switch in the housing. • SERVICE (cont.) Timer Single set timer shown Multi set timer (Urn/Carafe) similar Location: The timer is located on the timer bracket in the grinder base.